Forced Air Draft Cooling Systems
All parts on this page are special order items and will be shipped directly to you by truck only, no UPS or Mail.
Forced air will not work in the home with refrigerators for runs over five feet. A home fridge do not have the BTU rating (cooling capacity) - KegMan suggests you use the Home Glycol Plans for fridges.
The heart of the KegMan Cold Forced Air draft line cooling systems are the blower and flexible Aluminum Tubing which when properly installed will deliver ice cold beer or wine up to 25 feet from your walk in cooler. Remember that every ninty degree bend will subtact 5 feet from the capability of the blower. Never try to push cold air up more than a couple of feet.
Before you order one of these components you must understand that cold air may not be the solution to your beer line cooling. A few facts from experience.
- Every 90° bend in the conduit is equivalent to 5 feet of length.
- Home refrigerators do not have the cooling capacity for running a 60 cfm
blower continuously when the temperature rise is more than 2°F.
If you do the fridge temperature will rise.
Home refrigerator runs should be kept to 6 inches or less with no bends. - 15 cfm blowers are for direct draw carts where the external run is no more
than 15 inches. - Commercial establishments should call before ordering so our designers can assist you with your installations.
- In most instances over 25 feet a Glycol or DIY Water system will more than pay for itself in enjoyment and efficiency.
Other air system components are listed below to meet the needs of every tavern and bar owner. For Beer Components for beer line switches, wall brackets, and couplings are on another page.
 | ||
| Complete Blower Assemblies | ||
|---|---|---|
| 6751 | 60 cfm for 2 inch flex tubing for distances up to 15 feet. | $113.26 |
| 6752 | 140 cfm for 3 inch flex tubing (shown on left) for distances up to 20 feet | $153.75 |
| 6753 | 265 cfm for 3 or 4 inch flex tubing for distances up to 25 feet | $162.50 |
 | ||
| Blowers, less cord, hanger & extension | ||
|---|---|---|
| 6755 | 15 cfm for direct draw carts | $75.46 |
| 6759 | Hanger bracket for 15 cfm blower | $42.25 |
| Flexible Aluminum Tubing for commercial use | ||
|---|---|---|
 | ||
| 6765 | 2 inch O.D. Flex Duct (per 25 foot section) | $87.75 |
| 6766 | 2.5 inch O.D. Flex Duct (per 25 foot section) | $101.25 |
| 6767 | 3 inch O.D. Flex Duct (per 25 foot section) | $113.06 |
| 6768 | 4 inch O.D. Flex Duct (per 25 foot section) | $143.43 |
| Insulation, Flexible Foam, Closed Cell | ||
|---|---|---|
| 6771 | 3.5 inch Foam Insulation (6 feet) | $30.78 |
| 6772 | 4.5 inch Foam Insulation (6 feet) | $34.83 |
| Separators Kit for Draft Tower | ||
|---|---|---|
| 6781 | Separators Kit for Draft Tower (3'' hole) | $80.23 |
The purpose of a KegMan long draw system is to provide ice cold beer to places removed from the keg cooling area. There are three types of systems used to provide cold beer at long distances: These are:
- FOB (Foam Control Detectors)
- Gas Blenders
- Nitrogen Generators
- Trunk Line (Python)
- Beer Pumps
- Glycol Power Pack Systems
- Pharmaceutical Grade Propolene Glycol
- DIY Home Glycol Plans to save $$$
- Hose Splicers
- Hose Tees
- Hose Clamps
- Cold Forced Air Systems
- 4 Product Flash Chillers
- How do I balance a draft system? Answer
- How much resistance is in my beer line? Answer
- Custom Cold water systems(Call)
Return to Top of Page.
Copyright © 1996 - 2007 Crossfire Engineering Inc.
Webmaster
